24/7 emergency response · Missouri & Kansas Call (816) 848-4231

Service line

Water Mitigation

Extraction, moisture mapping, controlled removal, and structural drying performed to ANSI/IICRC S500. The job is finished when the readings say so.

What this work is

Water does not stay where it landed. It migrates through subfloors, wicks up gypsum, and settles into wall cavities that look dry from the room side. Our first task is to find its boundary: non-invasive meters for scanning, pin meters for the readings that go on record, and thermal imaging as a screening aid. From that map we determine the Category of contamination and the Class of drying load under ANSI/IICRC S500, set a dry standard from unaffected materials in your building, and assign a drying goal to every affected material. That is the baseline every later decision is judged against.

Then we remove what cannot be saved and dry what can. Porous materials contacted by grossly contaminated water come out, bagged and sealed inside containment. Structurally sound materials wetted by clean water are frequently dried in place with targeted methods, which preserves finishes and shortens downtime. Air movers and dehumidification are sized to the evaporation load, readings are logged at least daily, and the equipment plan changes the day the numbers stop trending down. Antimicrobials are used only when warranted, only EPA-registered products, and only with your signed consent. Your close-out file carries the whole record.

Commercial dehumidifier and air mover set up for structural drying in an affected room
Dehumidification sized to the evaporation load

Per ANSI/IICRC S500

Category and Class

Every water loss is classified twice: by the contamination of the water, and by the drying load it leaves behind. Both determinations go on the record before equipment is placed.

Category
Category 1

Water from a sanitary source, such as a broken supply line or a clean overflow, that poses no substantial risk from contact. Often dried in place. S500 notes that category can degrade with time and temperature, so a clean loss left wet does not stay clean.

Category
Category 2

Water with significant contamination, such as dishwasher or washing machine discharge, hydrostatic seepage, or toilet overflow without feces, with the potential to cause discomfort or illness on contact. Porous materials are evaluated carefully and often removed.

Category
Category 3

Grossly contaminated water that can carry pathogenic or toxigenic agents: sewage, backflow from beyond the trap, rising flood water. Gypsum wallboard and other porous materials it contacts are removed and replaced rather than dried.

Class
Class 1

The least water absorption and the lowest evaporation load. A small portion of the space is wet and little of it is porous material.

Class
Class 2

Significant water absorption and evaporation load. A substantial portion of the floor, wall, or ceiling surface is wet, including porous materials.

Class
Class 3

The greatest absorption and evaporation load, often from water entering overhead, with most of the surfaces in the space affected.

Class
Class 4

Deeply held or bound water in low-permeance materials such as hardwood, plaster, concrete, and masonry. Requires specialty drying methods, longer drying times, and higher vapor-pressure differentials.

The same standard, calibrated to the building

Water mitigation for the building you have

A hospital, an office tower, and a family home carry different risks and different rules, and the plan is written for the one you have.

For healthcare

In a hospital, a water loss is an infection-control event.

VeraPoint dries healthcare buildings the way your infection prevention team would if they ran a drying crew: under your ICRA permit, behind sealed negative-pressure containment, and with a record of every reading. Performed to ANSI/IICRC S500 and the CDC/HICPAC environmental infection control guidelines.

A burst supply line above a med-surg unit is not a plumbing problem with a patient-safety footnote. It is a patient-safety problem that happens to involve plumbing. Wet gypsum and ceiling tile can become a fungal reservoir within days, the CDC guidelines give you a 72-hour window to dry or remove absorbent materials, and every hour the HVAC keeps moving air across a damp cavity is potential exposure for the people who can least afford it. The restorer you call has to understand all of that before the first air mover is set.

VeraPoint Restoration was founded by healthcare professionals who have stood on the other side of the containment wall. We know what a surveyor asks to see, what an infection preventionist needs in the file, and why a unit that stays open with a verified barrier is worth more to you than a unit closed for a week. Our water mitigation follows ANSI/IICRC S500, the industry's standard of care for water damage restoration, layered with the construction-precaution discipline your own ICRA already demands. Clinical standard is not a slogan here. It is the training we came from.

Water-damaged ceiling with collapsed drywall and exposed cavity above a room
Wet ceiling cavity: a 72-hour clock under CDC guidance

What's at stake

The barrier is only as good as the crew behind it

A poly wall with a gap at the ceiling deck is theater, not containment. Healthcare water losses need critical barriers sealed to the structure, HVAC supplies and returns blocked, and negative pressure that is actually measured, not assumed.

Survey readiness does not pause for a leak

When The Joint Commission or a CMS surveyor walks the floor, the file on last month's water event is fair game. If the contractor cannot produce the ICRA permit, daily pressure logs, and drying records, the finding lands on the facility, not the vendor.

Closing beds is the most expensive mitigation strategy there is

Diverting a surgical suite or taking a wing offline costs more per day than most restoration invoices. The work has to be phased around census, procedure schedules, and after-hours windows so the smallest possible footprint is out of service for the shortest possible time.

How the work runs

1

Triage with your infection prevention team, not around them

Before equipment rolls, we classify the water per ANSI/IICRC S500: Category 1 (clean source), Category 2 (significantly contaminated), or Category 3 (grossly contaminated, such as sewage or backflow from beyond the trap), and the Class of intrusion based on how much surface area is wet and how porous the materials are. S500 notes that category can degrade with time and temperature, so the clock matters. We bring that determination, the affected-area map, and the patient risk group of the adjacent spaces to your infection preventionist so the ICRA precaution class is set together. Gray or black water in an occupied unit will typically push the precaution class up; we plan for that rather than argue about it.

2

Build containment to the precaution class, then prove it

Under your ICRA permit we install critical barriers sealed floor to deck, isolate or block HVAC supplies and returns serving the area, and establish negative pressure inside the work zone using HEPA-filtered negative air machines exhausted outdoors or through HEPA, consistent with the CDC/HICPAC recommendation for work zones adjacent to patient-care areas. For Class IV and V precautions we add an anteroom for donning and doffing, tacky mats at the entry, and continuous pressure monitoring. The differential is read and logged daily against your facility's permit threshold, and that log is yours.

3

Extract, map, and set drying goals before anything is removed

We extract standing water, then map the boundary of moisture migration with non-invasive meters for scanning and pin meters for the readings that go on record, with thermal imaging as a screening aid. Per ANSI/IICRC S500 we establish a dry standard from unaffected materials of the same type in your building and set a drying goal for each affected material. This is the baseline every later reading is judged against, and it is what tells us whether a wall can be dried in place or has to come out.

4

Remove what cannot be saved, under negative pressure

ANSI/IICRC S500 lists gypsum wallboard among the porous materials that should be removed and replaced, not dried, after Category 3 contact, and the CDC guidelines call for removing absorbent materials that cannot be cleaned and dried within 72 hours. We cut, bag, and seal debris inside containment, wet-wipe or HEPA-vacuum carts before they leave, and route them along the path your facility designates. Above-ceiling work is enclosed and kept under negative pressure with HEPA exhaust. Where antimicrobials are warranted, and S500 is clear that they generally are not for a Category 1 loss that has not changed category, we use only EPA-registered products selected with your infection prevention team, provide the label and SDS, and obtain signed written consent first.

5

Dry to the goal, read the psychrometrics every day

Air movers deliver continuous airflow across every wet surface, including wall cavities where the water category allows them to be dried in place, with HEPA air filtration devices running whenever air is moving through cavities that cannot be fully cleaned. Low-grain refrigerant or desiccant dehumidification is sized to the evaporation load. Temperature, relative humidity, and grains per pound are recorded at least daily in the affected area, an unaffected reference area, outdoors, and at dehumidifier inlets and outlets, alongside moisture content for every mapped material. Readings should trend down; if they do not, the equipment plan changes that day, not at the end of the week.

6

Verify, clean, and close out with a file your surveyor can read

Containment comes down only after every material has reached its drying goal, the work zone has been HEPA-vacuumed and wet-wiped, and your infection preventionist has signed off on the final inspection. If visible mold growth or suspected contamination is found, we stop, bring in an independent indoor environmental professional as S500 contemplates, and the project moves under ANSI/IICRC S520 with third-party post-remediation verification rather than our own say-so. Your close-out package includes the ICRA permit and precaution class, daily negative-pressure logs, the moisture map with dry standard and drying goals, daily psychrometric and moisture logs, photo documentation of removed materials, equipment logs, any antimicrobial consent, and a certificate of completion. It is built for the infection prevention binder and the adjuster's file at the same time.

Standards that shape this work

Standard

ANSI/IICRC S500 (Standard for Professional Water Damage Restoration)

Defines how we categorize contamination, classify the drying load, set dry standards and drying goals, decide between drying in place and removal, handle antimicrobials, and document the job from first inspection to completion.

Standard

CDC/HICPAC Guidelines for Environmental Infection Control in Health-Care Facilities

Sets the healthcare overlay: the 72-hour dry-or-remove window for water-damaged materials, negative pressure in work zones adjacent to patient care, daily pressure documentation, HEPA exhaust, anterooms, and barrier maintenance.

Standard

ASHE ICRA 2.0 (Infection Control Risk Assessment)

Provides the activity-type and patient-risk-group matrix your facility uses to assign a precaution class, which dictates the barrier, pressure, anteroom, and permit requirements we build to.

Standard

ANSI/IICRC S520 (Standard for Professional Mold Remediation)

Governs the handoff when a water loss has already produced fungal growth, including containment, physical removal, and independent post-remediation verification before a space returns to service.

Why VeraPoint

We came from your side of the barrier

VeraPoint was founded by healthcare professionals. The reflexes that make a good clinician, including contamination awareness, closed-loop documentation, and respect for the chain of custody, are the reflexes we bring to a wet ceiling cavity. We do not need the ICRA explained to us, and we will not ask your infection preventionist to babysit the crew.

Every promise comes with its proof

Anyone can say 24/7 response. We pair the response with the record: the moisture map, the pressure log, the daily psychrometrics, the consent forms, the photos of what came out of the wall. If a surveyor or a carrier asks what happened in Room 412 last March, the answer is in a file, not in someone's memory.

Built to keep units open, not to make the job easy

Containment sized to the actual affected area, work phased around census and procedure blocks, after-hours and overnight crews when that is what the schedule demands, and one accountable project lead who talks to facilities, infection prevention, and environmental services in their own language. Our measure of success is how little of your building we take out of service.

Questions we hear

Can you work while the unit stays occupied?
Often, yes. The ICRA precaution class determined with your infection prevention team decides what the containment has to look like, and for most Class III and IV work a properly sealed, negative-pressure enclosure with HEPA exhaust allows adjacent patient care to continue. Highest-risk populations, such as oncology, transplant, or protective-environment rooms, require a more conservative plan and sometimes relocation, and we will tell you that honestly rather than overpromise.
What documentation will my infection prevention team and surveyors receive?
A complete close-out package: the ICRA permit and precaution class, daily negative-pressure readings for the life of the containment, the moisture map with dry standard and per-material drying goals, daily moisture and psychrometric logs, equipment logs, photographs of affected and removed materials, any antimicrobial labels and signed consent, and a certificate of completion. The same package serves your insurance carrier, so nothing has to be reconstructed later.
Does every water loss require tearing out drywall?
No. Under ANSI/IICRC S500, structurally sound materials wetted by clean, Category 1 water can frequently be dried in place with targeted methods such as wall-cavity drying, provided the drying goal can be reached before microbial growth begins. Category 3 water changes the answer: gypsum wallboard and other porous materials it contacts should be removed and replaced. The CDC guidelines add a healthcare-specific constraint, which is that absorbent materials that cannot be cleaned and dried within 72 hours should come out.
Do you perform air sampling for mold after a water loss?
Not as a routine step. The CDC guidelines do not recommend random, undirected environmental air sampling; they reserve it for epidemiologic investigations and other specific, targeted purposes. What we do verify is that every material has reached its drying goal and the work zone has been cleaned. If your infection prevention team wants targeted sampling for a highest-risk unit, that is a decision for them and an independent indoor environmental professional, and we support it. If visible growth or suspected contamination is found, the project shifts to ANSI/IICRC S520 and an independent indoor environmental professional performs post-remediation verification. We do not clear our own mold work.

Healthcare emergency line

Wet ceiling tile over a patient room? Call now.

Our 24/7 emergency line reaches a crew that already knows what an ICRA permit is. Tell us the unit, the source, and the patient population, and we will tell you what the containment looks like before we arrive. Serving Missouri and Kansas from Northeast Kansas City, with nationwide capability for health systems.

Emergency or planned, we answer

Water where it shouldn't be? Call now.

Crews mobilize from Northeast Kansas City around the clock. For scheduled work, assessments, and vendor onboarding, send us the details or follow the work on LinkedIn — we respond the same business day.

24/7 emergency line(816) 848-4231